alloymap.EnglishOunce Works ↗

AlloyMap 홈으로

Alufont-48

Alufont-48 / AlCu4TiMgAg (RHEINFELDEN ALLOYS) | 사형 주조 및 중력 금형 주조

제조사가 보고한 값입니다. 인증된 설계 허용값으로 사용하지 마세요. 출처 보기 ↗

출처 문서의 제목과 조건 설명은 출처 언어 그대로, 공정 항목의 값·보류 사유·검토 메모는 영어 그대로 표시하며 번역하지 않습니다. 숫자, 단위, 질별, 합금 지정도 번역하지 않습니다.

질별두께항복강도 MPa인장강도 MPa연신율 %
T64 · Sand casting명시 없음200–270370–43014–18
T6 · Sand casting명시 없음410–450460–5103–7
T6 · Gravity die casting명시 없음410–460460–5105–8

T64 조건: Original supplier in-house performance interval; separately cast and casting-extracted specimens are included (p. 75). No wall thickness is stated for these ranges. Parenthetical values are separate casting minima at wall thickness ≤20 mm.

T6 조건: Original supplier in-house performance interval; separately cast and casting-extracted specimens are included (p. 75). No wall thickness is stated for these ranges. Parenthetical values are separate casting minima at wall thickness ≤20 mm.

T6 조건: Original supplier in-house performance interval; separately cast and casting-extracted specimens are included (p. 75). No wall thickness is stated for these ranges. Parenthetical values are separate casting minima at wall thickness ≤20 mm.

화학 조성

검토를 마친 질량 백분율(wt%) 한계만 표시합니다. 비어 있는 한계는 다른 쪽 한계만 보고되었다는 뜻입니다.

The original branded supplier handbook p. 62 gives Alufont-48 chemistry in mass %; p. 76 says single composition numbers are maxima. The same document repeats the table on pp. 76–77, not as independent evidence. Its p. 79 chemical order is OCR-rendered differently and no numerical designation is printed for -48; no EN/AA equivalence is inferred. Performance ranges from pp. 62 and 79 do not carry a wall thickness. Bracketed values are separate casting minima for walls up to 20 mm under p. 75. No cycle count or stress ratio is given for p. 79 fatigue ranges.

원소 / 출처 표기하한 wt%상한 wt%
Si—0.05
Fe—0.1
Cu4.05.0
Mn0.010.5
Mg0.150.35
Zn—0.05
Ti0.150.35
Ag0.41.0

물리·열 물성

물성보고된 값단위조건
밀도2.79kg/dm³Supplier physical summary; heat-treatable alloy in heat-treated state; test temperature not separately reported
영률65–72GPaSupplier physical summary; heat-treatable alloy in heat-treated state; test temperature not separately reported
열팽창2310⁻⁶/KSupplier physical summary; heat-treatable alloy in heat-treated state; 20–200 °C
열전도율1.3W/(K·cm)Supplier physical summary; heat-treatable alloy in heat-treated state; 20–200 °C
전기전도도17–23MS/mSupplier physical summary; heat-treatable alloy in heat-treated state; temperature not separately reported
전기전도도29.5–39.5%IACSSupplier physical summary; heat-treatable alloy in heat-treated state; temperature not separately reported
선수축률1.3–1.5%Supplier physical summary; heat-treatable alloy in heat-treated state; sand casting; temperature not separately reported
선수축률0.8–1.2%Supplier physical summary; heat-treatable alloy in heat-treated state; gravity die casting; temperature not separately reported
용융·응고 범위525–645°CSupplier melt and solidification range; includes partial-melting onset from segregation in the cast structure

가공 특성

출처가 보고한 비교이며 인증된 한계값이 아닙니다.

물성보고된 값
T6 heat treatmentSolution heat treatment 525–530 °C for 8–16 h; quench water 20–80 °C; artificial ageing 160–180 °C for 6–7 h (supplier guidance; wall thickness not given here).

추가 물성 데이터

출처가 보고한 값, 규격 구간, 최솟값(이상), 상한(미만 또는 이하)을 표시합니다. 평균은 출처가 평균으로 보고한 경우에만 평균이라고 표기합니다. 사용하기 전에 조건을 비교하세요.

물성값조건
브리넬 경도105–120 HBWSand casting; T64; supplier performance range; wall thickness not reported
항복강도≥ 180 MPaSand casting; T64; supplier casting minimum at wall thickness ≤20 mm (handbook p. 75)
인장강도≥ 320 MPaSand casting; T64; supplier casting minimum at wall thickness ≤20 mm (handbook p. 75)
연신율≥ 7 %Sand casting; T64; supplier casting minimum at wall thickness ≤20 mm (handbook p. 75)
브리넬 경도≥ 100 HBWSand casting; T64; supplier casting minimum at wall thickness ≤20 mm (handbook p. 75)
브리넬 경도130–150 HBWSand casting; T6; supplier performance range; wall thickness not reported
피로 저항80–100 MPaSand casting; T6; supplier summary range; fatigue cycle count and stress ratio not reported
항복강도≥ 320 MPaSand casting; T6; supplier casting minimum at wall thickness ≤20 mm (handbook p. 75)
인장강도≥ 380 MPaSand casting; T6; supplier casting minimum at wall thickness ≤20 mm (handbook p. 75)
연신율≥ 2 %Sand casting; T6; supplier casting minimum at wall thickness ≤20 mm (handbook p. 75)
브리넬 경도≥ 125 HBWSand casting; T6; supplier casting minimum at wall thickness ≤20 mm (handbook p. 75)
브리넬 경도130–150 HBWGravity die casting; T6; supplier performance range; wall thickness not reported
피로 저항100–110 MPaGravity die casting; T6; supplier summary range; fatigue cycle count and stress ratio not reported
항복강도≥ 340 MPaGravity die casting; T6; supplier casting minimum at wall thickness ≤20 mm (handbook p. 75)
인장강도≥ 440 MPaGravity die casting; T6; supplier casting minimum at wall thickness ≤20 mm (handbook p. 75)
연신율≥ 3 %Gravity die casting; T6; supplier casting minimum at wall thickness ≤20 mm (handbook p. 75)
브리넬 경도≥ 130 HBWGravity die casting; T6; supplier casting minimum at wall thickness ≤20 mm (handbook p. 75)

근거

Primary Aluminium Casting Alloys handbook, 2016 — Alufont-48 — RHEINFELDEN ALLOYS GmbH & Co. KG

값마다 정확한 출처 위치 보기

공식 발행기관 페이지