alloymap.EnglishOunce Works ↗

AlloyMap 홈으로

Anticorodal-04

Anticorodal-04 / AlSi0.5Mg (RHEINFELDEN ALLOYS) | 사형 주조, 중력 금형 주조 및 고압 다이캐스팅

제조사가 보고한 값입니다. 인증된 설계 허용값으로 사용하지 마세요. 출처 보기 ↗

출처 문서의 제목과 조건 설명은 출처 언어 그대로, 공정 항목의 값·보류 사유·검토 메모는 영어 그대로 표시하며 번역하지 않습니다. 숫자, 단위, 질별, 합금 지정도 번역하지 않습니다.

질별두께항복강도 MPa인장강도 MPa연신율 %
F · Sand casting명시 없음60–10090–13015–20
T7 · Sand casting명시 없음160–180190–2103–5
F · Gravity die casting명시 없음80–120100–14018–22
T7 · Gravity die casting명시 없음170–190200–2203–6
F · High-pressure die casting명시 없음80–120100–1407–12

F 조건: Original-supplier performance interval; no wall thickness stated for the main range. Bracketed casting minima at wall ≤20 mm are separately recorded.

T7 조건: Original-supplier performance interval; no wall thickness stated for the main range. Bracketed casting minima at wall ≤20 mm are separately recorded.

F 조건: Original-supplier performance interval; no wall thickness stated for the main range. Bracketed casting minima at wall ≤20 mm are separately recorded.

T7 조건: Original-supplier performance interval; no wall thickness stated for the main range. Bracketed casting minima at wall ≤20 mm are separately recorded.

F 조건: Original-supplier performance interval; no wall thickness stated for the main range. HPDC values are test-piece measurements.

화학 조성

검토를 마친 질량 백분율(wt%) 한계만 표시합니다. 비어 있는 한계는 다른 쪽 한계만 보고되었다는 뜻입니다.

Original-supplier branded grade, not a generic AlSi0.5Mg equivalence. Main performance ranges have no stated wall thickness; p. 75 restricts bracketed casting minima to sand/gravity castings with wall thickness ≤20 mm. HPDC ranges are measured on test pieces and have no bracketed minima. The 2015 and 2016 official editions disagree on HPDC linear shrinkage, so that claim is withheld. REACH ingredient disclosure is not an ingot specification.

원소 / 출처 표기하한 wt%상한 wt%
Si0.30.6
Fe—0.8
Cu—0.01
Mn—0.01
Mg0.30.6
Zn—0.07
Ti—0.01

물리·열 물성

물성보고된 값단위조건
밀도2.67kg/dm³Supplier physical summary; heat-treatable alloy in heat-treated state; test temperature not separately reported
영률66–73GPaSupplier physical summary; heat-treatable alloy in heat-treated state; test temperature not separately reported
열팽창2310⁻⁶/KSupplier physical summary; heat-treatable alloy in heat-treated state; 20–200 °C
열전도율2.0W/(K·cm)Supplier physical summary; heat-treatable alloy in heat-treated state; 20–200 °C
전기전도도29–31.5MS/mSupplier physical summary; heat-treatable alloy in heat-treated state; temperature not separately reported
전기전도도50.0–54.0%IACSSupplier physical summary; heat-treatable alloy in heat-treated state; temperature not separately reported
선수축률1.1–1.2%Supplier physical summary; heat-treatable alloy in heat-treated state; sand casting; temperature not separately reported
선수축률0.8–1.1%Supplier physical summary; heat-treatable alloy in heat-treated state; gravity die casting; temperature not separately reported
용융·응고 범위600–650°CSupplier melt and solidification range; includes partial-melting onset from segregation in cast structure
밀도2.67g/cm³Manufacturer REACH technical information, 2015 version 2; at 20 °C; product form not further specified
용융 범위600–650°CManufacturer REACH technical information, 2015 version 2; measurement method not stated

가공 특성

출처가 보고한 비교이며 인증된 한계값이 아닙니다.

물성보고된 값
T6 general heat treatmentGeneral heat-treatment summary: solution 520–530 °C for 6–8 h; water quench at 20 °C; age 180–190 °C for 6–8 h.
T7 general heat treatmentGeneral heat-treatment summary: solution 520–530 °C for 6–8 h; water quench at 20 °C; age 220–240 °C for 4–6 h.
supplier qualitative characteristicsSupplier describes best corrosion resistance, very good weldability, suitability for decorative anodising except for high-pressure die casting, and suitability for hard soldering. These are supplier descriptions, not normalized test ratings.

추가 물성 데이터

출처가 보고한 값, 규격 구간, 최솟값(이상), 상한(미만 또는 이하)을 표시합니다. 평균은 출처가 평균으로 보고한 경우에만 평균이라고 표기합니다. 사용하기 전에 조건을 비교하세요.

물성값조건
브리넬 경도35–40 HBWSand casting; F; supplier performance range; wall thickness not reported
항복강도≥ 50 MPaSand casting; F; supplier casting minimum at wall thickness ≤20 mm
인장강도≥ 80 MPaSand casting; F; supplier casting minimum at wall thickness ≤20 mm
연신율≥ 10 %Sand casting; F; supplier casting minimum at wall thickness ≤20 mm
브리넬 경도≥ 35 HBWSand casting; F; supplier casting minimum at wall thickness ≤20 mm
브리넬 경도70–75 HBWSand casting; T7; supplier performance range; wall thickness not reported
항복강도≥ 150 MPaSand casting; T7; supplier casting minimum at wall thickness ≤20 mm
인장강도≥ 180 MPaSand casting; T7; supplier casting minimum at wall thickness ≤20 mm
연신율≥ 3 %Sand casting; T7; supplier casting minimum at wall thickness ≤20 mm
브리넬 경도≥ 70 HBWSand casting; T7; supplier casting minimum at wall thickness ≤20 mm
브리넬 경도40–45 HBWGravity die casting; F; supplier performance range; wall thickness not reported
항복강도≥ 70 MPaGravity die casting; F; supplier casting minimum at wall thickness ≤20 mm
인장강도≥ 90 MPaGravity die casting; F; supplier casting minimum at wall thickness ≤20 mm
연신율≥ 12 %Gravity die casting; F; supplier casting minimum at wall thickness ≤20 mm
브리넬 경도≥ 40 HBWGravity die casting; F; supplier casting minimum at wall thickness ≤20 mm
브리넬 경도70–80 HBWGravity die casting; T7; supplier performance range; wall thickness not reported
항복강도≥ 150 MPaGravity die casting; T7; supplier casting minimum at wall thickness ≤20 mm
인장강도≥ 190 MPaGravity die casting; T7; supplier casting minimum at wall thickness ≤20 mm
연신율≥ 3 %Gravity die casting; T7; supplier casting minimum at wall thickness ≤20 mm
브리넬 경도≥ 70 HBWGravity die casting; T7; supplier casting minimum at wall thickness ≤20 mm
브리넬 경도40–45 HBWHigh-pressure die casting; F; supplier performance range; wall thickness not reported
발화 온도400 °CManufacturer REACH technical information; dust form only; not bulk-alloy ignition temperature

검토 중인 데이터

선수축률 보류: Manufacturer 2015 overview reports 0.5–0.7%, while its 2016 handbook reports 0.5–1.0% for the same HPDC column. Revision or method is not explained; no value is published.

Aluminium Casting Alloys overview, 2015 — Anticorodal-04 ↗ — PDF p. 5, Anticorodal-04 physical-properties first row, HPDC linear shrinkage

Primary Aluminium Casting Alloys handbook, 2016 — Anticorodal-04 ↗ — PDF p. 81, Anticorodal-04 aligned physical-properties row, HPDC linear shrinkage

근거

Anticorodal-04 technical information (REACH), 2015 version 2 — RHEINFELDEN ALLOYS GmbH & Co. KG

Primary Aluminium Casting Alloys handbook, 2016 — Anticorodal-04 — RHEINFELDEN ALLOYS GmbH & Co. KG

값마다 정확한 출처 위치 보기

공식 발행기관 페이지